Logelloop

The most versatile looper

Slicer not triggering selections on Insert 2-5

You are here: Logelloop > Slicer not triggering selections on Insert 2-5

Home › Forums › Macros › Slicer not triggering selections on Insert 2-5

Viewing 8 posts - 1 through 8 (of 8 total)
  • Author
    Posts
  • 20 February 2024 at 23 h 11 min #6321
    Daniel AkerbergDanielAkerberg
    Member

    Hello,

    I have 5 Insert Loopers on Fx1-5 channels. I am using Slicer to trigger different selections on the Insert Loopers. In my current Slicer Preset I have set the exact same In and Out values for Insert 1, Insert 2, Insert 3 etc… (In the Edit matrix). And all of these Inserts are also enabled (red marked) in the UI. When Insert 1 is enabled the slicer works perfectly on Insert 1, but when I do the same for any of the other Inserts nothing happens. I am missing something or could there be a bug here? The Insert 1-8 buttons in the Slicer UI corresponds to Inserts on FX channels, right? Thanks!!

    21 February 2024 at 9 h 04 min #6323
    Philippe OllivierPhilippe
    Keymaster

    Hi,
    You probably forgot to set the slicer to inserts routing that is in the drawer at the bottom of the Slicer window.
    This is explained in the documentation.

    Here is a screen copy of my settings and everything seems to be ok.

    Best,
    Philippe

    Slicer Inserts settings

    • This reply was modified 9 months ago by Philippe OllivierPhilippe.
    21 February 2024 at 9 h 11 min #6324
    Philippe OllivierPhilippe
    Keymaster

    I think those settings should be set to 1-8 by default.
    It will be the case for in the next Logelloop release.

    21 February 2024 at 11 h 15 min #6327
    Daniel AkerbergDanielAkerberg
    Member

    Ok. Thanks!

    21 February 2024 at 19 h 36 min #6330
    Daniel AkerbergDanielAkerberg
    Member

    Now the triggering of Insert 2-5 works fine! However, I have found another strange behaviour that I cannot explain. When I have red marked/selected only “Slices” the selctions are swithcing in main looper in accordance to Slicer settings. In this case the Insert Loopers should not be affected at all by the Slicer (because no Insert 1-8 have been red marked), but what happens is that at the moment when Slicer is started all Insert Loopers get “stuck” in one selection from where the current playhead is located. This is very strange since nothing should happen to the Insert loopers. Any ideas?

    21 February 2024 at 19 h 44 min #6331
    Daniel AkerbergDanielAkerberg
    Member

    Apparently this is connected to if the specific FX 1-5 is connected to the Inserts 1-5 as per your picture above. If for example Fx 1 is not connected to an insert this Insert Looper does not get “stuck” in a selection

    26 February 2024 at 3 h 06 min #6348
    Philippe OllivierPhilippe
    Keymaster

    Hi Daniel,
    There was a bug here.
    Thanks for finding and reporting it.
    I think it is now fixed for the next release.
    I will send you a private link to download the next beta and tell me if this is also fixed on your end.
    Best,
    Philippe

    26 February 2024 at 10 h 53 min #6350
    Daniel AkerbergDanielAkerberg
    Member

    Thanks!

  • Author
    Posts
Viewing 8 posts - 1 through 8 (of 8 total)
  • You must be logged in to reply to this topic.